Product Information

Wire Stop® for 3/8" & 5/16" EHS Strand (Large)

(Is in the revised ANSI A300 Standards & conforms to all "shall" clauses)

Download Installation Instructions 

Download a detailed comparison 

101

1-24

25-49

50+

 100+

$21.50/each

$20.50/each

$20.00/each

$19.50/each

The internal taper of Rigguy's® Wire Stop® fits over the middle strand of 7-strand EHS cable with the six remaining strands surrounding it. The more pressure that is applied, the deeper into the block the strand and taper are pulled. The block is made of 6061 AL and taper is made of 416 SS for strength of application and corrosion resistance. Although the wire stop is only 1 1/4 inches long, it holds close to 100 percent of the breaking strength of the strand itself, which is more than 15,000 pounds (if using 3/8-inch EHS strand). The Wire Stop® eliminates the need for the "J," "lag," "eye," hooks, thimbles, "through bolts," "pre-formed wraps," "wire clips," or other terminal hardware. It can be used in more applications because it is secured on the outside of the limb or trunk. Because of its small size and simplicity, it makes a more finished, less cluttered, installation.

Wire Stop® Finishing Cap for 3/8" & 5/16" EHS Strand (Large)

101F

any

$2.00/each

The Finishing Cap is not a necessary component of the Wire Stop®. It does, however, give a finished appearance and protection from exposed wire ends. The cap is made of UV protected vinyl.

Wire Stop® for 1/4" & 3/16" EHS Strand (Small)

(Is in the revised ANSI A300 Standards & conforms to all "shall" clauses)

Download Installation Instructions

201

1-24

25-49

50+

$20.50/each

$19.50/each

$17.25/each

The same part as the Wire Stop® listed above except that it fits the smaller strands. (1/4"& 3/16")

Wire Stop® Finishing Cap for 1/4" & 3/16" EHS Strand (Small)

201F

any

$1.75/each

The Finishing Cap is not a necessary component of the Wire Stop®. It does, however, give a finished appearance and protection from exposed wire ends. The cap is made of UV protected vinyl.

Wire Stop® for ornamental trees using 3/16" EHS Strand

(Is in ANSI A300 Standards & conforms to all "shall" clauses)

Download Installation Instructions

301

any

$15.00/each

This Wire Stop® measures only 11/16" wide by 1/2" long. It was specifically developed for use on smaller trees. (Dogwoods, Bradfords etc.)

Wire Stop® Hub for all commonly used EHS strand applications (3/8", 5/16", 1/4", & 3/16")

(Conforms to ANSI A300 Standards "shall" clauses)

501

any

$27.00/each

The Wire Stop® hub is the middle of a hub and spoke system for joining three trunks or leaders together. Our hub solution is less damaging than triangulation because it only requires three holes instead of six. It also requires less than half the parts (13) required in a traditional system installation (31).

303DLX Heavy Duty Ship Augers

18" Over All Length x 15" Twist Length &
24" Over All Length x 21" Twist Length

18" OAL

24" OAL

any

$50.25/each 

$57.00/each
 

• Molybdenum coated for cooler running 
• Glides through wood with less binding, bores faster 
• Ejects chips faster 
• Stays sharper longer 
• No run out, machined to a true center

Buy augers 1/16" larger than EHS strand used. Ex. 1/4" strand buy 5/16" auger

18" OAL:
DLX 1/4", 5/16", 3/8", 7/16"

24" OAL:
DLX 1/4", 5/16", 3/8", 7/16"

KNIPEX Cutters

KN10

any

$72.00/each

¨     "Mini Bolt cutter" 10" cutter for cutting 1/4 - 5/16 - 3/8"  individual strands Not the whole 7 strand wire with one cut.

¨     Cuts material like bolts, nails, rives, up to 52mm dia.

¨     Exceptional cutting performance with minimum effort because of new lever action design.

¨     Cutting edges additionally induction hardened, cutting edge hardness approx. 64 hrc.